Even if you attempt to engage in this activity in PM's we will still enforce the forum rules. The same goes for any private transaction via Private Message.
Kenwood tk 880 1 software#
Making a request such as this is attempting to engage in software piracy and this forum cannot be involved or associated with this activity. All requests will be deleted and a forum infraction issued. Please do not make requests for copies of radio programming software which is sold (or was sold) by the manufacturer for any monetary value. Ï Be sure to leave enough slack in the cables so the transceiver can be removed for servicing while keeping the power applied.To anyone looking to acquire commercial radio programming software: Ï Locate the fuse as close to the battery as possible.Ĥ Coil and secure the surplus cable with a retaining band.
Kenwood tk 880 1 install#
Ï If no hole exists, use a circle cutter to drill the firewall, then install a rubber grommet.Ģ Run the two power cable leads through the firewall and into the engine compartment, from the passenger compartment.ģ Connect the red lead to the positive (+) battery terminal and the black lead to the negative (ñ) battery terminal. LOCATE THE POWER INPUT CONNECTOR AS CLOSE TO THE TRANSCEIVER ASġ Check for an existing hole, conveniently located in the firewall, where the power cable can be passed through. THE TRANSCEIVER OPERATES IN 12 V NEGATIVE GROUND SYSTEMS ONLY! CHECK THE BATTERY POLARITY AND VOLTAGE OF THE VEHICLE BEFORE INSTALLING THE TRANSCEIVER. Ï A 4.2 mm (5/32 inch) drill bit for the 5 x 16 mm self-tapping screws, and a 3.2 mm (1/8 inch) drill bit for the 4 x 16 mm self-tapping screws. Ï A 6 mm (1/4 inch) or larger electric drill. The following tools are required for installing the transceiver: When drilling mounting holes, be careful not to damage vehicle wiring or parts. Note: Before installing the transceiver, always check how far the mounting screws will extend below the mounting surface. Note: The following preparation instructions are for use by your KENWOOD dealer, an authorized KENWOOD service facility, or the factory.
VEHICLE AND ENLIST HIS AID IN DETERMINING IF THEY WILL PERFORM NORMALLY WHILE TRANSMITTING. IF YOUR VEHICLE CONTAINS SUCH EQUIPMENT, CONSULT THE DEALER FOR THE MAKE OF ELECTRONIC FUEL INJECTION, ANTI-SKID BRAKING, AND CRUISEĬONTROL SYSTEMS ARE TYPICAL EXAMPLES OF EQUIPMENT THAT MAY MALFUNCTION.
NOT PROPERLY PROTECTED FROM THE RADIO FREQUENCY ENERGY WHICH IS PRESENT VARIOUS ELECTRONIC EQUIPMENT IN YOUR VEHICLE MAY MALFUNCTION IF THEY ARE Reviewing Messages in the Queue Memory.Īutomatic Status Response. Do not transmit while the caps are being placed into or removed from the container. If you are transporting blasting caps in your vehicle, make sure they are carried in a closed metal box with a padded interior. Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. Operating the transceiver within 500 feet of dynamite blasting caps may cause them to explode. INJURY FROM RADIO FREQUENCY TRANSMISSIONSĭo not operate your transceiver when somebody is either touching the antenna or standing within two to three feet of it, to avoid the possibility of radio frequency burns or related physical injury. Do not carry spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area. Turn OFF your transceiver while taking on fuel or while parked in a gasoline service station. SAFETY: It is important that the operator is aware of, and understands, hazards common to the operation of any transceiver.ĮXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) REFER SERVICE TO QUALIFIED TECHNICIANS ONLY. ILLEGAL OPERATION IS PUNISHABLE BY FINE AND/OR IMPRISONMENT. GOVERNMENT LAW PROHIBITS THE OPERATION OF UNLICENSED RADIO TRANSMITTERS WITHIN THE TERRITORIES UNDER GOVERNMENT CONTROL. Ï If an abnormal odour or smoke is detected coming from the transceiver, turn OFF the power immediately. Ï Do not place the transceiver in excessively dusty, humid, or wet areas, nor on unstable surfaces. Ï Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. Ï Do not modify the transceiver for any reason. Ï Do not attempt to configure the transceiver while driving it is too dangerous. Please observe the following precautions to prevent fire, personal injury, and transceiver damage. As a result, we feel strongly that you will be pleased with the quality and features of this product. KENWOOD transceivers incorporate the latest in advanced technology. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. We are grateful you chose KENWOOD for your personal mobile applications.
0 kommentar(er)
